Maytag compact front-load washer error codes (2024)

Check/Repair

Make sure both water supply valves behind the washer are fully open. In winter, check the fill lines for freezing. Check the drain system for a siphon problem. If the water valve assembly is defective, replace it.

Check/Repair

Remove excess suds; the washer can't drain excessively sudsy water. Check your house drain system for a clog. Check the drain hose for kinks or clogs. Replace the drain pump if defective. If the washer drains properly, replace the water level pressure switch because it isn't accurately detecting the water level.

Check/Repair

Unplug the washer and, if the washer is overfilled, check the water valve assembly for proper water shut-off. If the water valve assembly is defective, replace it. If the washer is empty when this error code appears, replace the water level pressure switch.

Check/Repair

Unplug the washer and check the wire harness between the water temperature sensor and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wiring is okay, replace the temperature sensor.

Check/Repair

Unplug the washer and check the wire harness connections between the motor control board and the drive motor. Check the wire harness connections between the motor control board and the main electronic control board. Reconnect any loose wires or replace any damaged wire harnesses. If the wiring connections are okay, check to see if the spin basket rotates smoothly. If not, remove any obstruction between the spin basket and tub. If the spin basket rotates smoothly, replace the drive motor. If the problem continues, replace the motor control board.

Check/Repair

Unplug the washer and check the wire harness connections between the motor control board and the drive motor. Check the wire harness connections between the motor control board and the main electronic control board. Reconnect any loose wires or replace any damaged wire harnesses. If the wiring connections are okay, replace the drive motor. If the problem continues, replace the motor control board.

Check/Repair

Unplug the washer and clear any debris out of the catch on the door lock assembly. Replace the door lock assembly if damaged. If the assembly isn't damaged, check the wire harness connections between the door lock assembly and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged.

Check/Repair

The Electrically Erasable Programmable Read-Only Memory (EEPROM) on the main electronic control board is corrupted. Unplug the washer for 5 minutes, restore power and see if the code clears. If not, the replace the main electronic control board.

Check/Repair

Unplug the washer and check the wire harness connections on the main electronic control board, motor control board and drive motor. Reconnect any loose wires and replace any damaged wire harnesses. If there are no wire connection problems, replace the motor control board. If the problem continues, replace the main electronic control board.

Check/Repair

Remove clothes from the washer. The washer must be empty when running a washer cleaning cycle.

Check/Repair

Unplug the washer. Check the wire harness between the water level pressure switch and the main control board. Reconnect any loose wires or replace the wire harness if damaged. If the wiring is okay, replace the water level pressure switch.

Check/Repair

Unplug the washer and, if the washer is overfilled, check the water valve assembly for proper water shut-off. If the water inlet valve assembly allows water flow with the washer unplugged, replace the water inlet valve assembly because it's defective. If the washer is empty when this error code appears, replace the water level pressure switch.

Check/Repair

Unplug the washer. Check the wire harness connections between the drain pump and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wiring is okay, replace the main electronic control board because it detects an internal error in the electronic circuit that controls the drain pump.

Check/Repair

Unplug the washer. Check the wire harness connections on the motor control board, drive motor and main electronic control board. Reconnect any loose wires or replace any damaged wire harnesses. Replace the motor control board if you don't find any wiring problems.

Check/Repair

This code appears if the main electronic control board does not detect the door opening after 3 consecutive loads, indicating that the door switch may have failed. If you've started a cycle several times without opening the door, open the door to clear this code. The code also displays when the door switch is open with the door locked. Unplug the washer and check the wire harness connections between the door switch and the main electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wiring connections are okay, replace the door switch.

Check/Repair

The control detects that the door switch is open with the door locked. Push the door in and check to make sure it's completely closed. If the door is closing completely and the error occurs, replace the door switch. If the problem continues, replace the door lock assembly.

Check/Repair

If you see excessive suds in the washer, you're likely using too much high-efficiency (HE) detergent. Remove the wet clothes from the washer and add 1 tablespoon of vegetable oil to the tub to dissipate the excessive suds. Restart the washer on a normal cycle without adding any additional detergent. After the cycle ends, run the clean washer cycle with bleach added to rinse out suds residue from the washer tub. Reduce the amount of high-efficiency (HE) detergent that you use to avoid excessive suds.